• No special brackets to order or have made
• Correct stainless nuts and bolts supplied
• Precise pressure die cast means it fits first time, every time
• No selection guesswork - only 3 sizes fit all actuators and accessories

Eliminate Mounting Problems

• Stronger than fabricated brackets
• More accurate than fabricated brackets
• Fully enclosed design provides safety to assemblers and operators
• Standard and optional corrosion protection means a longer service life

Economical

• Lower priced than any custom manufactured bracket
• Install in just minutes
• No rework with die cast accuracy
• All mounting hardware supplied
• Low inventory costs with only 3 sizes for all applications

Increased Accessory Life

• Precision parallel faces eliminate side loads to shafts and bearings
• Accurate, consistent specified height means no up thrust to positioners and switch boxes
• Correct supplied mounting hardware assures secure attachment

High Quality

• Large capital investment in Aluminium pressure die castings means the SafeMount is low in cost but high in quality. Quality is assured through certified ISO 9001 management systems.

Stainless Steel Hardware

• The SafeMount is supplied with all necessary Stainless Steel bolts and washers.

Safety

• The SafeMount is fully enclosed. Fingers cannot get at the rotating shaft giving plant personnel maximum protection; an approaching International Safety Standard.

Reduced Inventory Costs

• No need to keep high inventories of high cost, custom made brackets. A maximum of three sizes will cover all your accessory to actuator requirements.

Strong & Accurate

• The SafeMount is engineered to be strong and accurate. No more bent and/or flexing mounting brackets. No more poorly aligned mounting holes. No more damage to accessory bearings and shaft seals. No more cut fingers from sharp bracket edges. SafeMount will pass the technicians "ladder" test.

Corrosion Resistance

• Our standard VEP50 ELECTROPHORETIC bonded black coating gives over 2000 hours protection in a standard salt spray corrosion test. Also available in CORROGARD 941 Fluoropolymer bonded coating for more aggressive environments.

Accessory mounting Holes

• The SafeMount fits both the old 2 ¹/₄" X 2 ¹/₄" mounting square and the VDI/VDE standard.

Dimensional Diagrams

	SAFEMOUNT SM 80/20 VDI/VDE 80mm x 30mm (3.15" x 1.18"). To Suit 20mm (0.79") high Namur Pinion. Overall height 45mm (1.77"). 1) 4 holes 6mm (0.24") DIA. Mounting Hardware on 80 x 30 (3.15" x 1.18") VDI/VDE 2) 4 holes 7mm (0.28") DIA. Mounting Hardware on ISO 50mm (1.97") PCD. 3) 4 holes 9mm (0.35") DIA. Mounting Hardware on 57.1mm (2.25") square (3.18" PCD).
	SAFEMOUNT SM 80/30 VDI/VDE 80mm x 30mm (3.15" x 1.18"). To Suit 30mm (1.18") high Namur Pinion. Overall height 55mm (2.17"). 1) 4 holes 6mm (0.24") DIA. Mounting Hardware on 80 x 30 (3.15" x 1.18") VDI/VDE 2) 4 holes 7mm (0.28") DIA. Mounting Hardware on ISO 50mm (1.97") PCD. 3) 4 holes 9mm (0.35") DIA. Mounting Hardware on 57.1mm (2.25") square (3.18" PCD).
	SAFEMOUNT SM 130/30 VDI/VDE 130mm x 30mm (5.12" x 1.18"). To Suit 30mm (1.18") high Namur Pinion. Overall height 55mm (2.17"). 1) 4 holes 6mm (0.24") DIA. Mounting Hardware on 130 x 30 (5.12" x 1.18") VDI/VDE 2) 4 holes 7mm (0.28") DIA. Mounting Hardware on ISO 50mm (1.97") PCD. 3) 4 holes 9mm (0.35") DIA. Mounting Hardware on 57.1mm (2.25") square (3.18" PCD).