One package for fiscal metering or gas quality

• Custody transfer analysis from C6+ to C9+
• Contaminant monitoring - trace H2S, CO2, oxygen, etc.
• Combine measurements and reduce analysis cost
• Oxygen (0-2%)
• Trace H2S (0-50 ppm)
• CO2 (as fast as 90 seconds)
• Helium/Hydrogen (0-10%)
• Hydrocarbon Dew Point (±2°C)

Reduced installation costs

• 24 VDC power standard
• Integrated controller electronics
• Pipe-mount, wall-mount, or floor mount

Lower operation and maintenance costs

• No shelter or instrument air required
• Low helium and power consumption
• Longest gas chromatograph valve and column warranties available

Unmatched measurement performance

• Highest stated precision ±0.25 BTU/1000 (10J/m3) for ambient C6+ analysis
• Wide dynamic range from percent to trace level components
• Reliable performance over broad ambient temperatures -30°C to 60°C (-20°F to 140°F)

Easy to use

• MON2000 software setup and diagnostics
• Identical setup and operation for all models
   — no additional training

• Integrated controller provides one package for fiscal metering or gas quality analysis
• Supports multiple detectors – TCD, FID, FPD – in a field mountable package
• Increased analytical capabilities in a reduced footprint
  

Power:
Standard: 24 VDC, (24.5-26.5 VDC)
Optional: 90-264 VAC, 47-63 Hz
80 watts start-up; 33 watts nominal

Environment: -29° to 60°C (-20° to 140°F)

Enclosure Protection Rating: IP66 and NEMA 4X

Dimensions (without sample system):
Wall-mount: 914mm H x 462mm W x 483mm D
(36” H x 18.2” W x 19” D)
Pipe-mount: 914mm H x 462mm W x 645mm D
(36” H x 18.2” W x 25.4” D)
Floor-mount: 1483mm H x 419mm W x 577mm D
(58.4” H x 16.5” W x 22.7” D)

Mounting: Free-standing (standard); wall-mount or pipe-mount (optional)

Approximate Weight (without sample system): 80 kg (175 lbs.)

Area Safety Certification Options:
CSA: Class 1, Division 1, Groups B, C, D, T4
         USA: Class I, Zone 1, Ex d IIB+H2, T4, Enclosure Type 4
         Canada: Class I, Zone 1, Ex d IIB+H2, T4, Enclosure Type 4
ATEX: Ex II 2G Ex d IIC T4 Tamb = 60°C

Oven: Airless heat sink, maximum 130°C (266°F)

Valves: 6-port and 10-port diaphragm chromatograph valves. Other types of valves may be used, such as liquid injection or rotary valves, depending on the application

Carrier Gas: Application-dependent. Typically zero-grade helium, nitrogen, or hydrogen

Sample Input Pressure Range (recommended): 15-20 psig

Carrier Gas Input Pressure Range (recommended): 90-100 psig

Detector: Thermal conductivity detector (TCD), flame ionization detector (FID), TCD/TCD or TCD/FID dual detector configurations possible; flame photometric detector (FPD) available (see FPD module data sheet)

Gating Options: Fixed-time automatic slope sense gating of peaks

Streams: Up to eight streams (including calibration stream) internally controlled; up to 12 streams externally controlled

Chromatograms stored/archived internally: Most recent analysis and/or calibration per stream

Analog Inputs: Four inputs filtered with transient protection (user scalable and assignable)

Analog Outputs: Four non-isolated analog outputs, 4 – 20 mA (standard); four additional isolated analog outputs or eight additional non-isolated analog outputs (optional)

Serial Communication Ports: Three serial ports standard with option for a total of seven. Depending on the port, choice of RS-232, RS-422, and RS-485 is available as well as the Modbus protocol

Digital Inputs: Five digital inputs; user assignable

Digital Outputs: One gas chromatograph alarm and four user-assignable outputs (2 form A, 3 solid-state optically isolated)

Parallel Printer Port: One parallel port available for printed reports

Internal Modem (optional): Field-configurable; 300 to 33.6k baud rate

Ethernet Card (optional): 10 mbps with RJ-45 port